Top Star XL Table Tennis Table
Model 7172-000
Adult Assembly Required
Picture Similar
Made in Germany
KETTLER® International, Inc. 1355 London Bridge Road Virginia Beach, VA 23453 USA
www.kettlerusa.com
[email protected]om
Please do not return this product to
the store. Contact KETTLER® for
parts and service: call toll free
866.804.0440 or send email to
[email protected]om.
Please visit our website
www.kettlerusa.com to view a video
demonstration of product assembly
or scan the QR Code above.
Tools needed; not included
2
All KETTLER
®
products are designed in accordance with the latest safety regulations and undergo a constant process of quality
control during manufacturing. The knowledge gained in this process is used to constantly improve and develop our products. In
order to offer our customers the very best in product quality, we reserve the right to make technical changes at any time. In spite
of this, should you have any cause for complaint, please contact KETTLER
®
.
Note on Safety
Handling the Equipment
The table tennis table should be used only for its
intended purpose, i.e. for playing with suitable table
tennis racquets and balls.
All other uses are prohibited and may be dangerous.
The manufacturer cannot be held liable for damage
or injury caused by improper use of the table.
Damage or worn components may endanger your
safety or shorten the lifespan of the table tennis
table. Replace worn or damaged components
immediately and remove the table from use until
this has been done. Use only spare parts
manufactured by KETTLER®.
The table tennis table complies with all safety
regulations. Incorrect repairs, alterations to the
design (removal of original parts, addition of other
components etc.) may endanger the safety of the
user.
Instruct other persons (in particular children) using
the table in its correct use, and draw their attention
to any potential source of danger, especially when
setting up or dismantling the table.
Caution: During assembly, keep all items out of
children’s reach (choking hazard – contains small
parts).
When setting up or dismantling the table, stay clear of
its folding radius.
When folded up, the table tennis table presents a
large surface to the wind. For this reason, ensure that
it is stored in a sheltered position.
The table tennis table may be pushed only in the
transport position otherwise there is a risk of injury.
The unit complies with the standard
EN 4468-1:2004.
Regularly check all screws, bolts, etc. to ensure they
are in good condition.
Warning: Children should not attempt to fold/unfold
table. May result in injury
Do not use the table tennis table until it has been
fully and correctly assembled and checked.
Ensure that indoor table tennis tables are not
exposed to dampness or rain. Keep them well away
from direct sources of heat. Should the surface
become warped, lay the table on a level surface for a
few days.
Set the table up on a level surface.
Do not cover it with a tarp, which can result in
condensation forming. We recommend the
weatherproof KETTLER® cover, part number 7032-
900. Cover should only be used when table is in
folded position.
For practicing without a partner, the table halves can
be folded up individually.
Do not use corrosive or abrasive materials to clean the
equipment. Ensure that such materials are not
allowed to pollute the environment. In most cases, a
slightly dampened cloth is sufficient.
Waste Disposal: KETTLER® products are recyclable. At
the end of its useful life, please dispose of correctly
and safely complying with your local facilities and
guidelines.
Store table in folded position when not in use.
3
General Assembly Instructions
The equipment must be assembled with care by two
adults.
Separate all the parts including the hardware.
Compare quantities with the package contents
section and that all items are undamaged. If there
are any problems, please contact KETTLER®.
Before assembling the equipment, study the
drawings and photos carefully then assemble in the
order shown.
Please note that there is always a danger of injury
when working with tools or doing manual work.
Therefore, please be careful during assembly.
Ensure that your working area is free of possible
sources of danger, for example don’t leave any tools
lying around. Always dispose of packaging material
in such a way that it may not cause any danger.
There is always a risk of suffocation if children play
with plastic bags!
The fastening items required for each assembly step
are shown at the beginning of the step. Use the
fastening items exactly as instructed.
Bolt all the parts together loosely at first, and check
that they have been assembled correctly. Then use
spanner for final tightening. Then check that all
screw connections have been tightened firmly.
For technical reasons, we reserve the right to carry
out preliminary assembly work (e.g. addition of
tubing plugs).
Please keep original packaging, so that it may be
used for transport at a later date, if necessary.
Goods may only be returned after prior arrangement
and in packaging that is safe for transportation (in
the original box if possible). It is important to
provide a detailed defect description/damage
report.
Number Included - 2
Number Included - 2
Number Included - 2
Number Included - 1
Number Incl – 4 non locking
Number Incl – 4 locking
Number Included - 2
Number Included - 2
Number Included - 3
Number Included - 2
Number Included - 2
4
Items below are shown at actual size
Number Included - 4
Number Included - 2
Number Included - 1
Number Included - 1
Number Included - 2
Number Included - 2
Number Included - 2
Number Included - 2
Number Included - 4
Number Included - 2
Number Included - 2
Number Included - 2
Number Included - 4
Number Included – 4
m8x110
Number Included – 4
m6x110
Number Included – 6
m8x60
Number Included – 4
m6x20
Number Included – 2
m6x16
Number Included – 4
3.9x25
Number Included – 4
3.9x16
Number Included – 3
4x30
5
Items below are shown at actual size
Number Incl – 4
m8
Number Incl – 2
m6
Number Incl – 4
m6
Number Incl – 2
Number Incl – 6
dia 25x8
Number Incl – 16
dia 16x8
Number Incl – 10
dia 12x6
Number Incl – 2
“1”
Number Incl – 2
“2”
Number Incl – 4
m12x6x3
End view and side view shown
Number Incl – 4
m12x6x15
Number Incl – 4
Number Incl – 2
Number Incl – 4
Number Incl – 2
Number Incl – 4
m6 locking
Tools Included
(not shown at actual size)
6
Begin the assembly of your table by carefully removing
the plastic wrap and all of the loose contents. Separate
the two table tops by removing the four plastic corner
protectors and the plastic side strips.
Step 1
Align footlock with stemtube.
Insert drift pin. There are two footlocks and
stemtubes. Assemble both as shown.
A
B
C
2 Required
2 Required
7
Step 2
Install locking wheels.
The grooves of the wheels should face inward.
Do not over torque; wheels should roll smoothly.
Push down foot lock to lock the wheels. Install locking
wheels on both wheelbase assemblies.
A
G
D
E
F
C
B
H
I
2 Required
m8x110
2 Required
m8
8 Required
dia 16x8
16x8
16x8
16x8
16x8
m8
8
Step 2 (continued)
Install non-locking wheels.
Do not over torque; wheels should roll smoothly.
Install non-locking wheels on both wheelbase assemblies.
2 Required
m8x110
2 Required
m8
8 Required
dia 16x8
A
B
G
C
H
D
E
F
m8
16x8
16x8
16x8
16x8
9
Step 3
2 Required
dia 25x8
4 Required
2 Required
m8x60
A
B
D
C
G
E
F
I
H
Install H-Pad to Flange (A-C).
Install crossbar between wheelbase assemblies.
Take note of wheelbase assembly positions.
The assembly thus far should match photo I.
25x8
10
Step 4
Assemble Racquet and Ball holder as shown.
B
C
A
3 Required
4x30
11
Step 5
Attach Racquet and Ball holder to the outside of one wheelbase assembly as shown.
2 Required
m6x16
2 Required
dia 12x6
2 Required
m6
C
D
B
A
F
E
12x6
m6
12
Step 6
Attach Glides to tops as shown.
Note the position of the Glide to the corresponding
table side.
4 Required
dia 12x6
4 Required
m6 locking
4 Required
B
A
D
C
K
F
J
G
H
I
E
12x6
m6
12x6
m6
13
Step 7
4 Required
m6x110
4 Required
m12x6x3
End view and side view shown
4 Required
m12x6x15
C
B
D
E
A
F
Assemble frame on each top as shown.
To line up holes stand legs up as shown in
I and J.
Ensure that the text on the crossbar is
upside down as shown in K.
Insert footcap into each leg as shown in L.
After completion of Step 7, the top with
frame attached should match M.
Jbar
Support Leg
14
Step 7 (continued)
Step 8
L
G
H
I
K
J
C
B
A
D
Temporarily
install safety
knobs to
wheelbases
for the top
assembly.
M
15
Step 9
C
B
A
D
E
Two adults are required to complete Steps 9-14.
Complete Step 9 and 10 for one top and then repeat for the other side.
Lock safety knob 1 in place (A, B).
Lift table and align the Glides with the Wheelbase (C, D)
On the opposite wheelbase, hold knob 2 in place while lowering top (D).
Release when Glide passes knob assembly.
16
Step 10
D
C
B
A
2 Required
m8x60
2 Required
dia 25x8
One adult is required to support top while another completes Step 10 assembly.
Bolt Crossbar to Wheelbase as shown.
Repeat Step 9 and 10 for the other top.
17
Step 11
Step 12
A
B
C
D
E
A
B
Open tops slightly. Have one adult hold tops in this position while second adult completes steps 12 to 14.
To open top, lock safety knob 1 in place. Go to opposite wheelbase and hold knob 2 while opening top. Release
knob 2. Repeat for other top.
Remove knobs.
18
Step 13
C
B
A
D
E
G
F
H
I
4 Required
m6x20
4 Required
dia 12x6
4 Required
m6
Assemble net post panel and
flange as shown.
m6
m6x20
12x6
19
Step 14
Step 15
4 Required
3.9x16
A
B
C
F
E
D
A
B
J
C
2 Required
Attach Safety Knobs.
Cover open holes on wheelbase without racquet holder.
Note: An additional racquet and ball holder can be purchased by calling KETTLER Parts
and Service Department at 866-804-0440 and requesting part number 7094-999 or visit
www.kettlerusa.com.
20
Step 16
B
A
D
C
F
E
G
Open table into playing position to continue.
To open table, lock knob 1 by pushing toward net post (A, B).
On opposite wheelbase, press and hold knob 2 while lowering top (C, D).
Release when Glide passes knob assembly.
Completed half will appear as shown in E.
Repeat A through E for other top (F).
G shows table in playing position.
21
Step 17
4 Required
3.9x25
2 Required
B
A
D
C
G
E
F
H
2 Screws
Install Shrouds to each Wheelbase.
3.9x25
22
Net Assembly
G
D
F
E
A
B
C
Slide Jpin through net (A, B).
Place Jpin in designated slots (C).
Tie string to tension tab (D).
Place string in slots over Jpin and net post. Adjust net tension by adjusting tension tab (E).
Screw Adjuster into underside of net post (F, G).
23
Remove Film
Folding Table (for solo playback or storage)
Remove protective plastic film from table
surface.
A
B
C
D
E
F
To properly fold the table, lock knob 1 by pressing toward the net post (A, B).
On opposite side of table, press and hold knob 2 while raising the table top (C).
Release knob 2 and raise the top completely (D, E, F).
F shows table in solo playback position.
Repeat A through F for other side to complete folding the table.
24
This KETTLER® Limited Warranty applies to products sold through the KETTLER® Authorized Dealer Network to the
original retail purchaser and authenticated by proof of purchase from a retailer located in the United States. Any
shipments made under this warranty will be shipped to the United States only. Any shipment outside of the United
States will be at the sole cost of the customer. This KETTLER® Limited Warranty is a manufacturer’s warranty and is
not changed or modified by additional warranties extended by individual retailers at the point of sale. Manufacturer
warrants this product to be free from defects in material at the time of the product’s tender of delivery for a period of 5
years for residential use. This Limited Warranty is not transferable and does not cover normal wear and tear (including,
but not limited to, damage and wear to tires, power shocks, drive belts and other non-durable parts). The liability of the
manufacturer under this Limited Warranty shall not include any liability for direct, indirect, or consequential damages
resulting from the defect. This Limited Warranty is void if the product is damaged by accident, unreasonable use,
improper service, failure to follow instructions provided, modification from its original state, or other causes determined
not arising out of defects in material.
This warranty gives you specific legal rights. Should this product become defective due to material within the warranty
period, contact KETTLER® Parts & Service Dept. by phone at 866.804.0440, fax at 757.563.9273, or email at
par[email protected].
THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, MADE BY EITHER THE DISTRIBUTOR OR THE
MANUFACTURER ON KETTLER® PRODUCTS, EXCEPT THE MANUFACTURER’S LIMITED WARRANTY
AGAINST DEFECTS IN MATERIAL SET OUT BELOW:
THIS LIMITED WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
AND OF ANY OTHER OBLIGATIONS OR LIABILITY ON THE PART OF THE MANUFACTURER. KETTLER®
NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN
CONNECTION WITH SUCH PRODUCTS.
25
Ordering Spare Parts
When ordering spare parts, always state the full model number, spare part number, the quantity required and the serial number.
Example order: Model 7136-500/ spare part number 70130761/ qty 1/ serial number …
Important: Spare part prices do not include fastening materials; if fastening material (bolts, nuts, washers, etc.) is required, this should be clearly
stated on the order by adding the words “with fastening material”.
Contact: KETTLER® International Inc., 1355 London Bridge Road, Virginia Beach, VA 23453 USA
Online: www.kettlerusa.com E-mail: [email protected] For parts/service: call 866-804-0440 or email [email protected]
Serial Number
26
27
Number
Description
Number
Required
Spare Part Number
for 7172-000
Outdoor
1
Top
2
94130115
2
Leg
2
94110761
3
Crossbar
2
94110819
4
Footcap
4
70130823
5
Support Leg
2
94110814
6
Clamp
8
10128028
7
Clamp for Glide
4
70131000
8
Jbar
4
94110822
9
Crossbar
3
94110712
10
Wheel (non-locking)
4
94110848
11
Wheel (locking)
4
94110847
12
Footlock
2
70130816
13
Wheelbase
2
94110825
14
Stemtube for locking wheel
2
70130847
15
Stemtube for non-locking wheel
2
70130848
16
Bolt M8x140
4
10206086
17
Spacer Sleeve 12x1.8x85
4
97201441
18
Safety Stop, Bottom
4
70130826
19
Safety Stop, Top for safety knob #2
2
70130827
20
Safety Stop, Top for safety knob #1
2
70130828
21
Spring (not illustrated)
2
25616011
22
Release Wire
4
25057020
23
Spacer Sleeve 10x1.9x16
10
97200573
24
Glide Set
2
94111159
25
Paddle Holder (back)
1
70130856
26
Paddle Holder (front)
1
70130857
27
Netpost
2
94110829
28
Net
1
94180128
29
Tension Tab for Net
2
10128002
30
Safety Panel
2
70130835
31
Sideshroud
2
70130849
32
Spacer Sleeve 12x6.4x15
4
10108131
33
Bolt M6x110 (not illustrated)
4
94110892
34
Spacer Sleeve 66mm
2
70130825
35
Spacer Sleeve 45 mm
4
70130525
36
Flange, Bottom
2
97201284
37
Flange, Top
2
97201819
38
Safety Knob #1
2
70130833
39
Safety Knob #2
2
70130834
40
Rivet 6x9.5
2
10418503
41
Plug (not illustrated)
2
10100169
42
H Pad (set of 4)
1
94180145
43
Plug
4
94110894
44
Hardware Bag (not illustrated)
1
94180186
28
©2013 KETTLER® All rights reserved. No part of this
manual may be reproduced, stored in a retrieval system,
or transmitted in any form, or by any means, such as
electronic, mechanical, photocopying or otherwise,
without the prior written permission of KETTLER®.
KETTLER
®
International Inc.,
1355 London Bridge Road,
Virginia Beach, VA 23453 USA
www.kettlerusa.com • E-mail: info@kettlerusa.com
For parts/service: call 866-804-0440 or e-mail
parts@kettlerusa.com
Docu 07.27.13