Installation & Operation Manual
L20-378 rev. 4 (10/18)
IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain this manual
for the life of the equipment:
Model #: ___________________________
Serial #: ___________________________
Date Purchased: ____________________
ENGLISH
Covering all Solstice & Solstice Supreme
With Matchless Ignition
Built after 08/2000
D
E
I
F
I
T
R
E
C
D
E
S
I
G
N
CIRET IFED
0063
TO THE PURCHASER, OWNER AND STORE MANAGER
Please review these warnings prior to posting them in a prominent location for reference.
ii
L20-378 rev.4 (10/18)
TO THE PURCHASER
Post in a prominent location the instructions to be followed in the
event that an operator smells gas. Obtain this information from
your local gas supplier.
FOR YOUR PROTECTION
DO NOT store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Do not spray aerosols in the vicinity of this appliance when it is
in operation.
WARNING
Improper installation, operation, alteration, adjustments, service
or maintenance can cause property damage, injury or death.
Read the installation, operating and maintenance instructions
thoroughly before installing, operation, servicing this appliance.
WARNING
Installation, maintenance and repairs should be performed by a
Pitco Authorized Service and Parts (ASAP) company technician
or other qualified personnel. Installation, maintenance or repairs
by an unauthorized and unqualified personnel will void the
warranty.
WARNING
Installation and all connections must be made according to
local codes in force. In the absence of local codes in North
America, the installation must conform with the National Fuel
Gas Code, ANSI Z223.1/NFPA 54 or the Natural Gas and
Propane Installation Code CSA B149.1 as applicable. In
Australia, the appliance must installed in compliance with
AS/NZS 5601.
WARNING
During the warranty period if a customer elects to use a non-
original part or modifies an original part purchased from Pitco
and/or its Authorized Service and Parts (ASAP) companies, this
warranty will be void. In addition, Pitco and its affiliates will not
be liable for any claims, damages or expenses incurred by the
customer which arises directly or indirectly, in whole or in part,
due to the installation of any modified part and/or received from
an unauthorized service center.
WARNING
This appliance, when installed, must be electrically grounded in
accordance with local codes, or in the absence of local codes,
with the National Electrical Code, ANSI/NFPA 70, or the Canadian
Electrical Code, CSA C22.2, as applicable and the hose must
comply with AS/NZS 1869 and be class B or D.
WARNING
Adequate means must be provided to LIMIT the movement or this
appliance without depending on the gas or electrical cord
connection. Single appliances equipped with legs must be
stabilized by installing anchor straps. All appliances equipped
with casters must be stabilized by installing restraining chains.
WARNING
An appliance equipped with casters and a flexible gas line must
be connected to the gas supply with a quick disconnect device.
In North America this quick disconnect must comply with ANSI
Z24.41. In Australia, the quick disconnect must comply with AS
4627.
WARNING
DO NOT alter or remove structural material on the appliance to
accommodate placement under a ventilation hood.
WARNING
If the appliance is equipped with a power cord and it is damaged,
it must be replaced by a Pitco Authorized Service and Parts
(ASAP) company technician, or a similarly qualified person in
order to avoid a hazard.
WARNING
The power supply must be disconnected before servicing,
maintaining or cleaning this appliance.
WARNING
The appliance is NOT jet stream approved. DO NOT clean the
appliance with a water jet.
WARNING
DO NOT attempt to move this appliance or transfer hot liquids
from one container to another when the unit is at operating
temperature or filled with hot liquids. Serious personal injury
could result if skin comes in contact with the hot surfaces or
liquids.
WARNING
DO NOT use an open flame to check for gas leaks!
WARNING
DO NOT sit or stand on this appliance. The appliance’s front
panel, tank, splash back, tank cover, workshelf, drain board is
not a step. Serious injury could result from slipping, falling or
contact with hot liquids.
WARNING
NEVER use the appliance as a step for cleaning or accessing the
ventilation hood. Serious injury could result from slips, trips or
from contacting hot liquids.
WARNING
The oil/shortening level should NOT fall below the minimum
indicated level line at any time. The use of old shortening can be
dangerous as it will have a reduced flash point and be more
prone to surge boiling.
WARNING
The contents of the crumb catch and/or filter pan of any filter
system must be emptied into a fireproof container at the end of
the frying operation each day. Some food particles can
spontaneously combust into flames if left soaking in certain
oil/shortening materials.
WARNING
Completely shut the appliance down when shortening/oil is being
drained from the appliance. This will prevent the appliance from
heating up during the draining and filling process. Serious injury
can occur.
WARNING
This appliance is intended for indoor use only.
WARNING
DO NOT operate appliance unless all panels and access covers
are attached correctly.
WARNING
It is recommended that this appliance be inspected by a qualified
service technician for proper performance and operation on a
yearly basis.
WARNING
There is an open flame inside this appliance. The unit may get
hot enough to set nearby materials on fire. Keep the area around
the appliance free from combustibles.
WARNING
DO NOT supply the appliance with a gas that is not indicated on
the data plate. If you need to convert the appliance to another
type of fuel, contact your dealer.
WARNING
If gas flow to appliance is interrupted, or pilots extinguish, wait 5
minutes before attempting to relight the pilot to allow any
residual gas in appliance to dissipate.
WARNING
Ensure that the appliance can get enough air to keep the flame
burning correctly. If the flame is starved for air, it can give off a
dangerous carbon monoxide gas. Carbon monoxide is a clear
odorless gas that can cause suffocation.
WARNING
Never add oil to the appliance when it is at operating
temperature. Splashing hot oil can cause severe injuries.
WARNING
Never add water to hot oil. Violent boiling can occur causing
severe injury.
WARNING
This appliance is intended for professional use only and should
be operated by fully trained and qualified personnel.
WARNING
Excessive loading or loading of over wet food can cause surge
boiling. The maximum cooking load must not exceed
(14T- 1.5lbs (0.68kg), 14-3 lbs (1.36 kg), 18- 5 lbs (2.27 kg)
WARNING
In North America, gas appliances equipped with casters must
be installed with connectors that comply with the Standard for
Connectors for Movable Gas Appliances, ANSI Z21.69.CSA
6.16 Latest Edition. This connection should include a quick
disconnect device that complies with the Standard for Quick
Disconnect Devices for Use With Gas Fuel ANSI Z221.41.CSA
6.9 Latest Edition. In Australia, an appliance equipped with
casters and a flexible gas line must be connected to the gas
supply with a quick disconnect device that complies with AS
4627 and a restraining cable. The restraining cable must not
exceed 80% of the length of the flexible gas line.
L20-378 rev.4 (10/18) 3
1. INSTALLATION ................................................................................... 6
1.1. CHECKING YOUR NEW APPLIANCE .......................................................................................... 6
1.2. INSTALLATION CLEARANCES ................................................................................................... 6
1.3. HEAT DEFLECTOR INSTALLATION (IF EQUIPPED) ................................................................. 6
1.4. LEG/CASTER INSTALLATION AND LEVELING ......................................................................... 7
1.4.1. GAS CONNECTION ................................................................................................................ 8
1.4.2. QUICK DISCONNECT CONNECTION ................................................................................... 8
1.4.3. FUEL SUPPLY LINE LEAK AND PRESSURE TESTING ...................................................... 8
1.4.4. INSTALLATION SETUP .......................................................................................................... 8
1.4.5. CE GAS TABLE (NOT APPLICABLE TO ALL MODELS) ...................................................... 9
1.4.6. OVERALL DIMENSIONS AND WEIGHTS ........................................................................... 12
1.5. ELECTRICAL CONNECTIONS ................................................................................................... 14
1.6. VENTILATION AND FIRE SAFETY SYSTEMS .......................................................................... 14
1.7. INSPECTION ................................................................................................................................ 15
1.8. INITIAL ADJUSTMENTS ............................................................................................................. 16
1.8.1. FILLING THE APPLIANCE ................................................................................................... 16
1.8.2. LIGHTING INSTRUCTIONS ................................................................................................. 16
1.8.3. PILOT FLAME ADJUSTMENT .............................................................................................. 17
1.8.4. MAIN BURNER SYSTEM ADJUSTMENT ............................................................................ 17
1.9. INITIAL CLEANING ..................................................................................................................... 18
1.10. OPERATIONAL FEATURES ................................................................................................... 19
1.10.1. BASIC OPERATIONAL FEATURES ..................................................................................... 20
1.10.2. OPERATION FEATURES SPECIFIC TO MODELS WITH FILTERS. .................................. 20
1.11. FILLING THE COOKER TANK ................................................................................................ 21
1.11.1. FILLING THE TANK WITH LIQUID SHORTENING .............................................................. 21
1.11.2. FILLING THE TANK WITH SOLID SHORTENING ............................................................... 21
1.12. APPLIANCE START UP .......................................................................................................... 22
1.13. COOKING ................................................................................................................................. 23
1.13.1. TIMER OPERATION ............................................................................................................. 23
4
L20-378 rev.4 (10/18)
1.13.2.
BASKET LIFT OPERATION .................................................................................................. 23
1.13.3. SPINFRESH
TM
....................................................................................................................... 23
1.13.4. ADDITIONAL CONTROLLER FUNCTIONS ........................................................................ 24
1.14. COOKING TIPS ........................................................................................................................ 24
1.15. APPLIANCE SHUTDOWN ....................................................................................................... 24
1.15.1. STANDBY MODE .................................................................................................................. 24
1.15.2. COMPLETE SHUTDOWN .................................................................................................... 25
2. PREVENTATIVE MAINTENANCE .................................................... 25
2.1. DAILY PREVENTATIVE MAINTENANCE................................................................................... 25
2.1.1. FILTERING WITH A FILTER DRAWER (IF EQUIPPED) .................................................... 25
2.1.2. FLUSH HOSE OPERATION (IF EQUIPPED) ....................................................................... 26
2.1.3. REPLACING THE FILTER MEDIA (IF EQUIPPED) ............................................................. 26
2.1.4. APPLIANCE INSPECTION ................................................................................................... 27
2.1.5. CLEANING THE COOK TANK .............................................................................................. 27
2.1.6. CLEANING THE CABINET ................................................................................................... 27
2.1.7. FILTER CLEANING (IF EQUIPPED) .................................................................................... 28
2.2. WEEKLY PREVENTATIVE MAINTENANCE .............................................................................. 28
2.3. MONTHLY PREVENTATIVE MAINTENANCE ........................................................................... 28
2.3.1. BOIL OUT PROCEDURE ...................................................................................................... 28
2.3.2. TEMPERATURE CHECK ...................................................................................................... 29
2.4. ANNUAL/PERIODIC PREVENTATIVE MAINTENANCE AND INSPECTION ............................ 29
2.4.1. SAFETY EVALUATION ......................................................................................................... 30
2.4.2. MECHANICAL INSPECTION ................................................................................................ 30
2.4.3. TEMPERATURE CONTROL SYSTEM ................................................................................. 30
2.4.4. FILTER SYSTEM (IF EQUIPPED) ........................................................................................ 30
2.4.5. GAS COMBUSTION SYSTEM .............................................................................................. 30
2.5. VENTILATION HOOD .................................................................................................................. 30
3. TROUBLESHOOTING ....................................................................... 31
3.1. POWER FAILURE ........................................................................................................................ 31
L20-378 rev.4 (10/18) 5
3.2.
HIGH TEMPERATURE LIMIT SWITCH....................................................................................... 31
3.3. DRAIN VALVE INTERLOCK & FLOAT SWITCH (NOT ON ALL MODELS) ............................. 31
3.4. SELF CLEANING BURNER SYSTEM (NOT ON ALL MODELS) .............................................. 31
3.5. RESETTING THE SELF CLEANING BURNER SYSTEM TEMPERATURE LIMIT SWITCH .... 32
3.6. TROUBLESHOOTING CHARTS ................................................................................................. 33
3.6.1. FRYER TROUBLESHOOTING CHART ............................................................................... 33
3.6.2. FILTER TROUBLESHOOTING CHART (IF EQUIPPED) ..................................................... 33
3.7. COMPUTER & DIGITAL CONTROLLER DISPLAYS (IF EQUIPPED) ...................................... 34
INSTALLATION
6
L20-378 rev.4 (10/18)
1. INSTALLATION
1.1. CHECKING YOUR NEW APPLIANCE
Your new Pitco appliance has been carefully packed into one crate. Every effort has been made to
ensure that it is delivered to you in perfect condition. As you unpack your new appliance, inspect each
of the pieces for damage. If something is damaged, DO NOT sign the bill of lading. Contact the
shipper immediately; the shipper is only responsible for 15 days after delivery. Check the packing list
enclosed with your appliance to ensure that you have received all the parts to the appliance. If you
are missing any parts, contact the dealer from whom the appliance was purchased. As you unpack
the appliance and its accessories be careful to keep the weight of the appliance evenly distributed.
Locate your Pitco model number and serial number on the inner door of the appliance and the find
the date purchased. Write this information on the front cover of this manual for future reference.
If you have completed the above steps that are applicable to the appliance you purchased, the
appliance is now ready to be installed. Although it may be possible for you to install and set up your
new appliance, it is STRONGLY recommended that you have this done by qualified professionals. A
qualified professional will ensure that the installation is safe and meets local building and fire codes.
1.2. INSTALLATION CLEARANCES
The clearances shown below are for combustible and non-combustible installations and will allow for
safe and proper operation of your appliance.
In addition to the above clearances there must also be at least 30 inches (76.2cm) of aisle space in
front of the unit.
1.3. HEAT DEFLECTOR INSTALLATION (IF EQUIPPED)
If the appliance requires a heat deflector, you will find a removable label at the rear top edge of the
unit. This label has instructions for positioning and installation of the heat deflector. Refer to the label
and the instructions below to install the deflector.
Combustible Construction Non Combustible Construction
Inches (centimeters) Inches (centimeters)
Back 6.0" (15.2cm) 0.0" (0.0cm)
Sides 6.0" (15.2cm) 0.0" (0.0cm)
Counter 6.0" (15.2cm) 6.0" (15.2cm)
Floor 9” (22.86 cm) 9” (22.86 cm)
WARNING
DO NOT sit or stand on this appliance. The appliance’s front panel, tank,
splash back, tank cover, work shelf, drain board is not a step. Serious
injury could result from slipping, falling or contact with hot liquids.
WARNING
DO NOT install this appliance next
to a water cooker. A splash over of
water into the hot oil may cause a
flash fire.
WARNING
DO NOT obstruct the flow of ventilation, or air openings
around the appliance. Adequate clearance around the
appliance is necessary for servicing and proper
component ventilation. Ensure that you meet the
minimum clearance requirements specified in this manual.
INSTALLATION
L20-378 rev.4 (10/18) 7
1. Remove the two self-drilling screws from the top, back area of the appliance.
2. Position the heat deflector so that the angled portion of the deflector is facing toward the front
of appliance. Secure the heat deflector to the back of the unit using the two previously removed
fasteners.
3. When properly installed the angled section of the heat deflector will extend over the flue
opening to redirect the heat. It SHOULD NOT cover the flue opening. Never allow anything to
block the flue opening; this will cause the appliance to over heat and inhibit proper combustion,
which could produce dangerous gases.
1.4. LEG/CASTER INSTALLATION AND LEVELING
When you receive your appliance it is completely assembled with the possible exception of the legs
(or casters). This appliance must be installed with legs or casters; it cannot be curb mounted. Curb
mounting will seriously inhibit this appliance’s ability to effect proper component ventilation. The
legs/casters must be installed before connecting the appliance to the power supply. The legs provide
the necessary height to meet sanitation requirements and assure adequate air supply to the
combustion system. Use the following procedure.
Required tools: 7/16 “ (12 mm) wrench and socket and a large pair of water pump pliers.
1. Lay the appliance on its back, being careful not to damage the splash back by pulling on it.
Protect the outside of the appliance with cardboard or a drop cloth when laying it down.
2. Attach each leg/caster with the hex head screws and nuts supplied. Each leg/caster requires
four ¼-20 x 5/8” hex head screws and nuts. Insure that all screws are tight.
3. Mount the screws from the inside of the appliance with the nut on the outside (bottom) of the
appliance. The nuts have lock washers attached to them, therefore it is not necessary to use
separate lock washers.
4. When all four legs/casters are securely
mounted, stand the unit up, being careful not
to put too much weight on any one leg.
Adjust the height and level the appliance by
adjusting the leveling devices (B) with water
pump pliers. On casters, loosen 2 screws (A)
before leveling, make your height
adjustments, then retighten.
WARNING
DO NOT install legs or casters, or perform
leveling procedure when appliance is in operation
or full of hot liquids. Serious injury could result.
CAUTION
To prevent equipment damage and/or personal injury, do not tilt the appliance onto any
two of its casters or legs, or pull the appliance by the splash back.
WARNING
This appliance must be installed with the legs or casters provided by the manufacturer.
INSTALLATION
8
L20-378 rev.4 (10/18)
1.4.1. GAS CONNECTION
Your gas appliance will give you peak performance when the gas supply line is of sufficient size to
provide the correct gas pressure. The gas line must be installed to meet the local building codes or
National Fuel Gas Code ANSI Z223.1 Latest Edition. In Canada, install the appliance in accordance
with CAN/CGA-B149.1 or .2 and local codes. In Australia, install the appliance in accordance with
AS/NZS 5601. Gas line sizing requirements can be determined by your local gas company or, in
North America, by referring to the National Fuel Gas Code, Appendix C, Table C-4 (for natural gas)
and Table C-16 (for propane). The gas line needs to be large enough to supply the necessary amount
of fuel to all appliances without losing pressure to any appliance. A properly sized and installed gas
line will deliver a supply pressure between 7.0” W.C. (17.4mbars, 1.74kPa) and 10.0”W.C.
(24.9mbars, 2.49kPa) natural gas or between 11.0”W.C. (27.4mbars, 2.74kPa) and 13.0” W.C.
(32.4mbars, 3.25kPa) for propane to all appliances connected to the supply line, operating
simultaneously at full demand. The pressure at the gas valve shall not exceed ½ PSI.
The gas supply connection to this appliance is located in the rear of the appliance approximately
10-1/2” (26.7 cm) from the floor of the appliance when legs are used.
Each appliance is equipped to operate on one certain fuel type. The type of fuel with which the
appliance is intended to operate is stamped on the data plate, which is attached to the inside of the
door.
WARNING
The fryer must be restrained from tipping to prevent spilling of hot liquid. The fryer shall
be restrained from tipping when installed, such as by connection to other appliances,
installation in an alcove, or by separate means such as a mechanical tie to structural
features. In the case where a mechanical tie is used, the fryer shall not be operated
without first checking that the mechanical tie is in place.
1.4.2. QUICK DISCONNECT CONNECTION
In North America, gas appliances equipped with casters must be installed with connectors that
comply with the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69.CSA 6.16
Latest Edition. This connection should include a quick disconnect device that complies with the
Standard for Quick Disconnect Devices for Use With Gas Fuel Appliances ANSI Z21.41.CSA 6.9
Latest Edition. In Australia, an appliance equipped with casters and a flexible gas line must be
connected to the gas supply with a quick disconnect device that complies with AS 4627 and a
restraining cable. The restraining cable must not exceed 80% of the length of the flexible gas line.
The restraining device should be attached to the appliance at the back panel.
1.4.3. FUEL SUPPLY LINE LEAK AND PRESSURE TESTING
The fuel supply system must be tested before the appliance is used. If the fuel line is going to be
tested at a pressure greater than ½ PISG (3.45 kPa, 34.5 mbar), insure that that appliance is
disconnected from the fuel line. If the fuel line is to be tested at a pressure equal to or less than ½
PSIG (3.45 kPa, 34.5 mbar), the appliance can be connected during the test, but the unit’s gas
valve must be shut. Test all gas line connections for leaks with a solution of soap and water when
pressure applied.
1.4.4. INSTALLATION SETUP
The installation of this appliance MUST conform to local codes. In the absence of local codes in
North America, the installation must conform with the National Fuel Gas Code, ANSI
Z223.1/NFPA 54 or the Natural Gas and Propane Installation Code CSA B149.1 as applicable. In
Australia, the appliance must installed in compliance with AS/NZS 5601 (current revision).
WARNING
NEVER supply the appliance with a gas other than the one that is indicated on the data
plate. Using the incorrect gas type will cause improper operation and could result in serious
injury or death. If you need to convert the appliance to another type of fuel, contact the
dealer
y
ou
p
urchased it from.
NOTICE
NEVER use an adapter to make a smaller gas supply line fit the appliance connection. This
may not allow proper gas flow for optimum burner operation, resulting in poor performance
and improper operation.
INSTALLATION
L20-378 rev.4 (10/18) 9
1.4.5. CE GAS TABLE (NOT APPLICABLE TO ALL MODELS)
Refer to the following table for gas specifications for the country of use. If the country of use is
NOT listed, refer to the information stamped on the data plate.
NOTICE
If this appliance cannot be adjusted to perform correctly contact your local authorized
service company or call the factory at the number on the back of this manual.
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #40 YES 2.4
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
20.2 50/37 25.4 #54 LP16 YES 0.8
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #37 YES 3.6
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
30.4 50/37 25.4 #53 LP16 YES 1.2
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #36 YES 4.0
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
33.1 50/37 25.4 .062" LP16 YES 1.4
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #43 YES 3.3
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
27.6 50/37 25.4 1.45 mm LP16 YES 1.1
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 10 #38 YES 4.4
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
36.8 50/37 25.4 #53 LP16 YES 1.5
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #38 YES 4.4
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
36.8 50/37 25.4 #53 LP16 YES 1.5
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #44 YES 2.6
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
21.5 50/37 25.4 #55 LP16 YES 0.9
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #44 YES 2.6
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
21.5 50/37 25.4 #55 LP16 YES 0.9
SG14R 36
SG6H 40
MGII 23.4
MGIIT 23.4
G20
SG14T 30
SG18 40
Nat
G20
Gas
Appliance
Category
Gross
Input (kW)
Nat
G20
Nat
YES
#43 YES 2.1
N2210
#43/#40
Applicable
Countries
Nat
20
20/25
Nominal Gas
Rate (m3/hr)
Model
Fuel Type
Net
Input (kW)
Supply
Pressure (mbar)
Burner
Pressure (mbar)
Burner
Orifice
Pilot
Orifice (code)
Governor
SGC 22
SG14 33
Nat
G20
G20
G20
27.0
20
20/25
3.1
#41/#37 3.1/3.6
Nat 32.4 10 N22
YES#38
2.1/2.4
19.8
Nat
G20
29.7 10
#41
N22
YES 2.9
#43/#41 2.9/3.3
N22
20
20/25
20
20/25
10
#43
#38/#36
3.4
3.4/4.0
2.2
3.8
36.0
20/25 9/10 #41/#38 3.8/4.4
20 9 #41
N22
YES
3.8
#41/#38 3.8/4.4
YES
Nat
G20
21.1
20
10
20/25
N22
36.0
20
10
20/25
N22
#41
20/25 #46/#44 2.2/2.6
YES 2.2
2.2/2.6
#46
#46/#44
21.1
20
10
#46
N22
YES
INSTALLATION
10
L20-378 rev.4 (10/18)
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #44 YES 2.6
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
21.5 50/37 25.4 #55 LP16 YES 0.9
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #44 YES 2.6
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
21.5 50/37 25.4 #55 LP16 YES 0.9
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
TR
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #45 YES 2.2
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
18.4 50/37 25.4 #56 LP16 YES 0.8
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
TR
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #45 YES 2.8
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
23.0 50/37 25.4 #56 LP16 YES 0.9
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
TR
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #37 YES 3.9
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
32.2 50/37 25.4 0.0625" LP16 YES 1.3
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #45 YES 2.8
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
23.0 50/37 25.4 #56 LP16 YES 0.9
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #41 YES 4.9
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
40.5 50/37 25.4 1.45 mm LP16 YES 1.7
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #39 YES 6.8
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
56.6 50/37 25.4 1.5 mm LP16 YES 2.3
SGM20 25
SGM24 44
SGM34 61.5
Nat
G20
SGH50 23.4
SGH50T 23.4
Nat
G20
Nat
G20
SGM18D4
Nat
G20
20
SGM18D5
Gas
Appliance
Category
Gross
Input (kW)
Applicable
Countries
Nominal Gas
Rate (m3/hr)
Model
Fuel Type
Net
Input (kW)
Supply
Pressure (mbar)
Burner
Pressure (mbar)
Burner
Orifice
Pilot
Orifice (code)
Governor
Nat
G20
21.1
20
10
#46
21.1
20
10
#46
N22
YES#48
#48/#45
2.4
2.4/2.8
N22
#44 4.2
#44/#41
N22
YES#42 5.9
#42/#39 5.9/6.8
4.2/4.9
YES
N22
YES 2.2
20/25 #46/#44 2.2/2.6
2.2
20/25 #46/#44 2.2/2.6
N22
YES
22.5
20
10
20/25
20
10
20/25
55.4
39.6
Nat
G20 20
10
20/25
1.9
20/25 #48/#45 1.9/2.2
#48
N22
YES
18.0
20
10
#48
N22
YES
2.4
20/25 #48/#45 2.4/2.8
SGM1824
Nat
G20
35
31.5
20
10
#40
N22
YES 3.3
20/25 #40/#37 3.3/3.9
Nat
G20
25
22.5
20
10
INSTALLATION
L20-378 rev.4 (10/18) 11
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #44 YES 2.6
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
21.5 50/37 25.4 #55 LP16 YES 0.9
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #40 YES 3.4
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
27.0 50/37 25.4 1.55 mm LP16 YES 1.1
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
TR
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #44 YES 2.6
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
21.5 50/37 25.4 #55 LP16 YES 0.9
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
TR
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #40 YES 3.4
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
27.0 50/37 25.4 1.55 mm LP16 YES 1.1
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
TR
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #44 YES 2.6
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
21.5 50/37 25.4 #55 LP16 YES 0.9
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #40 YES 3.4
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
27.0 50/37 25.4 1.55 mm LP16 YES 1.1
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #43 YES 3.4
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
27.0 50/37 25.4 #55 LP16 YES 1.1
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #40 YES 4.1
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
33.7 50/37 25.4 1.55 mm LP16 YES 1.4
N22
YES#43 3.5
#43/#40 3.5/4.1
Nat
G20
33.0
20
10
20/25
SSH55 23.4
SSH55R 29.3
SSH55T 23.4
Nat
G20
Nat
G20
Nat
G20
Gas
Appliance
Category
Gross
Input (kW)
SSH60W 29.3
SSH60WR 36.6
SSH55TR 29.3
SSH60 23.4
SSH60R 29.3
Nat
G20
Nat
G20
Applicable
Countries
Nominal Gas
Rate (m3/hr)
Model
Fuel Type
Net
Input (kW)
Supply
Pressure (mbar)
Burner
Pressure (mbar)
Burner
Orifice
Pilot
Orifice (code)
Governor
2.2YES
21.1
20
10
20/25
20/25
21.1
20
10
21.1
20
10
2.8/3/4
2.2
20/25 #46/#44 2.2/2.6
#46
N22
YES
N22
YES 2. 2
#46/#44 2.2/2.6
Nat
G20
26.4
20
10
#43
26.4
20
10
20/25
#46/#44 2.2/2.6
#46
#46
N22
2.8#43
#43/#40 2.8/3/4
Nat
G20
26.4
20
10
26.4
20
10
#43
YES 2. 8
2.8/3/420/25
N22
YES
#46
N22
N22
N22
#46/#43
YES
YES 2. 8
20/25 #43/#40 2.8/3/4
2.8
20/25 #43/#40
INSTALLATION
12
L20-378 rev.4 (10/18)
Appliance Model Number
Height with Legs (cm)
Width in (cm)
Depth in (cm)
Approximate
Shipping Weight
lbs (kg)
Total Cook Area cm
2
SGC 30-9/32" (76.9) 14 (35.6) 14 (35.6) 150 (68.04) 196 (1267.3)
SG14,14R 14 (35.6) 14 (35.6) 208 (95) 196 (1267.3)
SG14T, SG14TR 7 (17.8) 14 (35.6) 230 (104) 98 (633.7)
SG18,18R 18 (45.7) 18 (45.7) 226 (103) 324 (2088.5)
SG6H 69-1/16" (175.4) 14 (35.6) 18 (45.7) 300 (136.08) 252 (1626.9)
14 (35.6) 14 (35.6) 208 (95) 196 (1267.3)
7 (17.8) 14 (35.6) 230 (104) 98 (633.7)
SGH50 14 (35.6) 14 (35.6) 208 (95) 196 (1267.3)
SGH50T 7 (17.8) 14 (35.6) 230 (104) 98 (633.7)
SGM18D4 18 (45.7) 18 (45.7) 226 (103) 324 (2088.5)
SGM18D5 18 (45.7) 18 (45.7) 226 (103) 324 (2088.5)
SGM20 20 (50.8) 20 (50.8) 310 (181) 400 (2580.6)
SGM24 24 (61) 24 (61) 375 (170) 576 (3721)
SGM34 34 (86.4) 24 (61) 495 (225) 816 (5270.4)
SGM1824 18 (45.7) 24 (61) 250 (113) 432 (2787.7)
SSH55,55R 14 (35.6) 14 (35.6) 208 (95) 196 (1267.3)
SSH55T,55TR 7 (17.8) 14 (35.6) 230 (104) 98 (633.7)
SSH60,60R 14 (35.6) 18 (45.7) 226 (103) 252 (1626.9)
SSH60W,60WR 18 (45.7) 14 (35.6) 275 (124.5) 252 (1626.9)
SSH75,75R 18 (45.7) 18 (45.7) 275 (124.5) 324 (2088.5)
46-1/8" (117.5)
48-1/4" (122.6)
MG2,MG2T
46-1/8" (117.5)
46-1/8" (117.5)
45-3/4 (116.2)
41-1/4" (105.4)
1.4.6. OVERALL DIMENSIONS AND WEIGHTS
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #45 YES 3.4
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
28.3 50/37 25.4 1.35 mm LP16 YES 1.2
AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE,
IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE,
I
2H
LU I
2E
FR I
2ESI
BE G20/G25 I
2E+
NO
DE G20/G25 I
2ELL
YES
NL G25 I
2L
25 #40 YES 4.1
BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT,
LU, MT, NL, PL, PT, RO, ES, SI, SK, TR
LP G31 I
3P
33.7 50/37 25.4 1.55 mm LP16 YES 1.4
N22
YES#45 2.9
#45/#43 2.9?3.4
Nat
G20
33.0
20
10
#43
N22
YES 3.5
20/25 #43/#40 3.5/4.1
Nat
G20
27.7
20
10
20/25
SSH75R 36.6
Gas
Appliance
Category
Gross
Input (kW)
SSH75 30.8
Applicable
Countries
Nominal Gas
Rate (m3/hr)
Model
Fuel Type
Net
Input (kW)
Supply
Pressure (mbar)
Burner
Pressure (mbar)
Burner
Orifice
Pilot
Orifice (code)
Governor
INSTALLATION
L20-378 rev.4 (10/18) 13
Nat #43 4.0
LP #54 10.0
Nat #41 4.0 Nat 2.4 mm 0.9
LP #53 10.0 LP 1.5 mm 2.5
Nat #38 4.0 Nat 2.6 mm 0.9
LP .062" 10.0 LP .062" 2.5
Nat #43 4.0 Nat #44 0.9
LP 1.45 mm 10.0 LP #55 2.5
Nat #41 4.0 Nat 2.3 mm 0.9
LP #53 10.0 LP 1.5 mm 2.5
Nat #41 4.0
LP #53 10.0
Nat #46 4.0
LP #55 10.0
Nat #46 4.0
LP #55 10.0
Nat #46 4.0
LP #55 10.0
Nat #46 4.0
LP #55 10.0
Nat #48 4.0
LP #56 10.0
Nat #48 4.0
LP #56 10.0
Nat #40 4.0
LP 0.0625" 10.0
Nat #48 4.0
LP #56 10.0
Nat #42 4.0
LP 1.45mm 10.0
Nat #42 4.0
LP 1.5 mm 10.0
Nat #46 4.0 Nat #46 1.0
LP #55 10.0 LP #55 2.5
Nat #46 4.0 Nat #46 1.0
LP #55 10.0 LP #55 2.5
Nat #43 4.0
LP 1.45 mm 10.0
Nat #43 4.0
LP 1.45 mm 10.0
Nat #46 4.0 Nat #46
1.0
LP #55 10.0 LP #55
2.5
Nat #43 4.0
LP 1.45 mm 10.0
Nat #46 4.0 Nat #46
1.0
LP #55 10.0 LP #55
2.5
Nat #43 4.0
LP 1.45 mm 10.0
Nat #45 4.0 Nat #45
1.0
LP 1.35mm 10.0 LP 1.35mm
2.5
Nat #43 4.0
LP 1.45 mm 10.0
NOT APPROVED FOR USE IN THIS
COUNTRY
SSH60W
R
SSH75
116
Mj/hr
SSH75R
SSH60
88 Mj/hr
SSH60R
SSH60W
110
Mj/hr
NOT APPROVED FOR USE IN THIS
COUNTRY
NOT APPROVED FOR USE IN THIS
COUNTRY
NOT APPROVED FOR USE IN THIS
COUNTRY
NOT APPROVED FOR USE IN THIS
COUNTRY
NOT APPROVED FOR USE IN THIS
COUNTRY
SGM1824
SGM24
NOT APPROVED FOR USE IN THIS
COUNTRY
NOT APPROVED FOR USE IN THIS
COUNTRY
NOT APPROVED FOR USE IN THIS
COUNTRY
SSH55 88 Mj/hr
SSH55T 88 Mj/hr
SSH55R
SSH55TR
NOT APPROVED FOR USE IN THIS
COUNTRY
NOT APPROVED FOR USE IN THIS
COUNTRY
SGC
SG14 119 Mj/hr
SG14R 129 Mj/hr
NOT APPROVED FOR USE IN THIS
COUNTRY
NOT APPROVED FOR USE IN THIS
COUNTRY
SGM34
MGIIT
80kBtu
(23.4kW)
SGH50
80kBtu
(23.4kW)
SGH50T
80kBtu
(23.4kW)
SGH50T
MGII
MGIIT
SGH50
120kBtu
(35.0 kW)
SGM24
165kBtu
(48.3kW)
US and Canada
Model
Gas
Type
SSH60W
100 kBtu
(29.3 kW)
SSH60W
R
125 kBtu
(36.6 kW)
SGM18D4
SGM18D5
SGM20
NOT APPROVED FOR USE IN THIS
COUNTRY
NOT APPROVED FOR USE IN THIS
COUNTRY
NOT APPROVED FOR USE IN THIS
COUNTRY
140kBtu
(40kW)
SG6H
SG14T 100 Mj/hr
SG18 145 Mj/hr
SG6H
NOT APPROVED FOR USE IN THIS
COUNTRY
Orifice Tip
Size
Burner
Pressure
Gross
Input
Australia
SSH60R
100 kBtu
(29.3 kW)
SGM34
SSH55
80 kBtu
(23.4kW)
SSH55T
80 kBtu
(23.4 kW)
SSH55R
100 kBtu
(29.3 kW)
Model
Gross
Input
210kBtu
(61.5 kW)
SSH55TR
100 kBtu
(29.3 kW)
SSH60
SG14R
122kBtu
(36kW)
SG14T
100kBtu
(30kW)
SG18
SSH75
105 kBtu
(30.8 kW)
80 kBtu
23.4 kW
Orifice Tip
Size
Gas
Type
Burner
Pressure
(in. W.C.)
140kBtu
(40kW)
MGII
80kBtu
(23.4kW)
SGC
75kBtu
(22kW)
SG14
110kBtu
(33kw)
SGM18D4
65kBtu
(19 kW)
SGM18D5
85kBtu
(25 kW)
SGM20
85kBtu
(25 kW)
SSH75R
125 kBtu
(36.6 kW)
SGM1824
INSTALLATION
14
L20-378 rev.4 (10/18)
1.5. ELECTRICAL CONNECTIONS
It is advised that this power supply be plugged into a wall receptacle that is controlled by the
ventilation control. This will prevent the appliance from being operated without the ventilator on. If
your appliance requires an electrical connection, the power requirements are listed below.
1.6. VENTILATION AND FIRE SAFETY SYSTEMS
Your new appliance must have proper ventilation to function safely and properly. Exhaust gas
temperatures can reach as high as 1100 °F (593 °C). Therefore, it is very important to install a fire
safety system. Your ventilation system should be designed to allow for easy cleaning. Frequent
cleaning and proper maintenance of the ventilation system and the appliance will reduce the chances
of fire. Ventilation and fire safety systems must comply to local and national codes for US and
Canada. Refer to ANSI 83.11 for a list of reference documents that will provide guidance on
ventilation and fire safety systems. For installations in U.S. and Canada, additional information can
be obtained from CSA International, 8501 East Pleasant Valley Road, Cleveland, OH, 44131 or visit
their website at www.csa-international.org. In Australia the ventilation system must comply with
AS/NZS 5601.0.
It is essential that the appliance be operated only when adequate ventilation is provided. Your
ventilation hood should be properly maintained. A qualified installation professional should ensure that
the hood is operating properly in conjunction with the appliance. Inadequate ventilation may not
properly evacuate appliance all emissions. Excessive or unbalanced ventilation may cause drafts,
which could interfere with proper operation of the pilot and burners. Leave at least 18 inches (47cm) of
open space between the flue of the appliance and the intake of the exhaust hood.
CAUTION
Connecting the appliance to the wrong power supply may damage the appliance and void
the warranty.
WARNING
This appliance must be connected to a power supply having the same voltage and phase as
specified on the data plate located on the inside of the appliance door.
WARNING
DO NOT attempt to connect the appliance to an electrical supply other then that indicated
on the data plate. Electrical connection should be performed by qualified personnel.
WARNING
The electrical connection used by this appliance must comply with local codes. In the
United States if there are no local codes that apply, refer to the National Electrical Code
(NEC), ANSI/NFPA 70 for installation in the US. In Canada, refer to CSA Standard C22.2 and
local codes. In all other cases
,
refer to local and national codes and re
g
ulations.
North America International
Input Voltage 120 VAC, 50/60 Hz 220, 230 or 240 VAC 50/60 Hz
Current per unit 1.0 Amp 0.5 Amps
Filter Current 7.5 Amp 4.2 Amps
Heat Tape 0.4 Amp 0.2 Amps
WARNING
If your appliance is equipped with an oil proof, electrical supply cord with a three-prong
safety plug. This is to protect operators from electrical shock hazard in the event of an
equipment malfunction. DO NOT cut or remove the grounding (third) prong from this plug; it
should be
p
lu
gg
ed into a
p
ro
p
erl
y
g
rounded three-
p
ron
g
r
ece
p
tacle.
INSTALLATION
L20-378 rev.4 (10/18) 15
If your appliance is equipped with SPINFRESH
TM
, the tank enclosure can interfere with the
performance of pre-existing fire safety systems. Modifications to the fire safety system should be
performed by a professional who is qualified in installing, designing and maintaining your fire safety
system prior to operating any SPINFRESH
TM
appliance.
For Australia, the fryer must be installed in accordance with AS/NZS 5601, local authority and any other
relevant statutory regulations. Flexible hose (if used) must comply with AS/NZS 1869 Class B or D, be of
appropriate internal diameter, be kept as short as possible (not exceed 1.2 meters), must not be kinked
and not be in contact with a hot surface. A chain must be fitted to restrict the fryer movement to no more
than 80% of the hose length.
1.7. INSPECTION
Before you begin filling and adjusting the appliance, perform the following visual checks:
After the appliance is in its permanent location, check the levelness. Any additional leveling that
is necessary can be performed as previously described.
Ensure that the probe and high temperature limit is in place and secure. Check the high limit
bulb mounting screws to ensure that they are tight.
Review the installation portion of this manual and ensure that all steps have been followed and
executed properly.
1) Probe
2) High Temperature Limit
WARNING
Ensure that your ventilation system does not cause a down draft at the appliance’s flue
opening. A down draft will not allow the appliance to exhaust properly and will cause
overheating, which may cause permanent damage. Damage caused by down drafts will not
be covered by the warranty. NEVER allow anything to obstruct the flow of combustibles or
ventilation exiting the appliance. NEVER place anything on top of the flue area, or block the
flue in any way. Never place a grease condensing drip pan over the flue opening.
WARNING
NEVER connect the ventilation blower or hood directly to the flue of this appliance. The
resulting increased flow of air through the combustion system will cause improper
operation, poor temperature recovery, poor ignition and could extinguish the pilot.
WARNING
Replacing or adding appliances under a pre-existing fire safety system may require
modifications to the system. ALWAYS contact a professional who is qualified in installing,
designing and maintaining your fire safety system to assure that any appliances located
under the fire safet
y
s
y
stem are adequatel
y
protected.
INSTALLATION
16
L20-378 rev.4 (10/18)
ON
OFF
DRAIN VALVE CLOSED
Solid State
I/0 ON/OFF
Switch
Solid State Melt
Switch
1.8. INITIAL ADJUSTMENTS
After your appliance has been properly installed as described in the installation section of this
manual, it will need to be adjusted to ensure that it will perform as designed. A qualified person must
perform these adjustments.
To perform these adjustments the following tools will be needed:
Manometer
Digital Thermometer (Temperature Probe)
DC Microammeter
DC Voltmeter
1.8.1. FILLING THE APPLIANCE
Refer to the following procedure to fill the cook tank prior to operation.
1. Ensure that the drain valve is closed.
2. Fill the tank with oil/shortening until the oil/shortening
reaches the level line(s). Never let the oil/shortening level
go below the MIN LEVEL mark stamped on the tank.
1.8.2. LIGHTING INSTRUCTIONS
There is nothing to manually light on the electronic ignition system. Pilot ignition is performed and
controlled by the electronic ignition system. Refer to the following instructions to light the
appliance.
1. Open the gas supply valves to the appliance.
2. Turn the gas valve knob to the ON position.
3. Turn the controller on.
Solid State Thermostat:
Assure the Melt switch is in the correct position.
Turn the I/0 (ON/OFF) switch to the I (ON) position
Computer and Digital Control:
Press the
*
button to turn the controller on.
*The specified button may appear slightly different then shown. Refer to
the operator’s manual for your appliance’s specific control type to
determine the exact appearance of each button and display.
4. The main burners will light and be controlled by the thermostat.
Note: If your appliance has a self cleaning burner system, the burners may make a
popping sound immediately after the main burners light during startup. This noise during
startup is part of the normal operation of the self cleaning burner system and should NOT
continue during normal cooking & idle periods. (SCB Only)
WARNING
Oil/shortening must completely cover the heat tubes at all times while appliance is on.
CAUTION
This appliance is not designed for cooking with water. Fill with oil/shortening only.
WARNING
During operation there is an open flame inside this appliance. The unit may get hot enough to
set near by materials on fire. Keep the area around the appliance free from combustibles.
INSTALLATION
L20-378 rev.4 (10/18) 17
OFF
ON
A) Burner Pressure Tap
B) Pilot Adjustment Screw Cap
C) ON/OFF Knob
D) Burner Pressure Adjustment Screw Cap
E) Inlet Pressure Tap
1.8.3. PILOT FLAME ADJUSTMENT
Perform this procedure with the pilot lit.
Note: This procedure requires the use of a DC microammeter.
1. Connect the DC microammeter between the flame
sensor terminal and the flame sensor lead. Observe
proper polarity: if the meter needle goes below 0,
reverse the leads. The current reading must be 1.0 A
or greater, (0.15 A or greater for CE units).
2. Adjust the current reading to the required level by
adjusting the pilot flame. Remove the pilot adjustment
screw cap screw to expose the pilot adjustment screw.
Turning the pilot adjustment screw clockwise will
decrease the size of the pilot flame and flame sense
current. Turning the pilot adjustment screw
counterclockwise will increase the pilot flame size and
the flame sense current.
3. Rotate the screw in the direction needed to achieve a
reading of 1.0 A or greater, (0.15 A or greater for CE
units).
Note: Allow 3 to 5 minutes between flame adjustments
to allow the reading to stabilize.
4. Once the pilot flame has been adjusted properly,
replace the pilot adjustment screw cap screw and
remove the microammeter.
1.8.4. MAIN BURNER SYSTEM ADJUSTMENT
For the main burners to operate the gas supply valve must be open and the thermostat must be
turned on. The main power switch must be on. The main burners receive gas from the main gas
supply through the thermostatically controlled valve. When the oil temperature drops below the
preset temperature the gas control valve opens.
The main burners must be adjusted to deliver optimum flame. Refer to the following procedure to
adjust the main burners.
1. Ensure that the main gas valve is shut off, remove the manifold pressure tap plug and
connect an accurate pressure gauge (range of 0-16 “W.C. (39.85mbar, 3.98kPa) in 0.1”
(.25mbar, .02kPa) increments) or manometer.
2. Turn on this and all appliances connected to the gas supply line and light their main burners.
The pressure reading of the installed pressure gauge should not drop from the required
installation pressure. Any loss of pressure indicates inadequate supply line installation,
which will cause poor performance of all appliances during peak usage.
3. The installed pressure gauge should be the same, ±0.1” W.C. (.25mbar, .02kPa), as that
marked on the data plate on the inside door of the appliance. If the pressure is correct, go to
step 6, if it is not, adjust the pressure as outlined in step 4.
WARNING
Do not store flammable materials in or near this appliance. Do not spray aerosols in the
vicinity of this appliance while it is in operation. Contact a qualified service person or the
factory, using the information on the back of this manual, if the appliance produces unusual
odor, yellow tipping flames or is not performing as per the original installation.
INSTALLATION
18
L20-378 rev.4 (10/18)
4. To adjust the pressure, remove the regulator adjustment screw cap and, with a flat head
screwdriver, adjust the regulator screw until the proper burner pressure is reached. Turning
the screw clockwise will increase the burner pressure. Turning the screw counterclockwise
will decrease the burner pressure.
5. When the pressure is correct, replace the regulator adjustment screw cover.
6. Turn off the ALL appliances, shut the main gas valve to your Pitco appliance and remove the
pressure gauge. Apply pipe joint compound to the manifold pressure tap plug and reinstall it.
1.9. INITIAL CLEANING
When your appliance is shipped, many of its parts are covered with a thin coat of oil for protection.
Before the appliance is ready for cooking all transit material must be removed and the appliance must
be cleaned. This will remove the oil coating and any foreign matter that may have accumulated during
storage and shipment. Refer to the following procedure to clean the appliance.
1. Read the “operation” section of this manual prior to filling or operating the appliance.
2. The following steps should be followed using a grease dissolving commercial cleaner.
3. Following the manufacturer’s directions, clean the tank interior and all other food contact
surfaces.
4. When cleaning is complete, rinse the inside of the tank thoroughly with cool water. Continue
to rinse the tank until the cleaner has been completely and thoroughly rinsed from the tank.
5. Using a clean dry cloth, wipe out all of the water.
6. Repeat the previous steps to clean the bread and batter station or filter pan if equipped.
If the appliance can’t be adjusted to operate properly contact a qualified service person or contact the
factory using the contact information on the back of this manual.
CAUTION
Be careful not to disturb the probe and high temperature
limit during operation and cleaning of this appliance.
WARNING
Wear protective gloves and clothing when cleaning and draining the appliance and
when disposing of water. The water is extremely hot and can cause severe injuries.
CAUTION
DO NOT leave the appliance unattended during cleaning. Never let the liquid level
go below the heat tubes.
WARNING
Use a commercial grade cleaner formulated to effectively clean and sanitize food
contact surfaces. Read the directions and precautionary statements before use.
Particular attention must be paid to the concentration of cleaner and the length of
time the cleaner remains on the food contact surfaces.
OPERATION
L20-378 rev.4 (10/18) 19
OPERATION
An operator’s manual for your appliance’s specific control type should be included with this manual.
Refer to that manual prior to operating this appliance.
1.10. OPERATIONAL FEATURES
The diagram below outlines some of the key operational components of your appliance. Refer to the
following sections of this manual to learn more about these features.
7
8
9
5
6
4
10
11
6
3
2
4
OPERATION
20
L20-378 rev.4 (10/18)
1.10.1. BASIC OPERATIONAL FEATURES
1. Cook Tank
2. Front Panel
If the appliance is equipped with a computer or digital controller, it will be located on the front
panel.
3. Door (Shown Open)
Provides access to,
the drain valve handle, tank drain outlet and high temperature reset button
Solid State (if equipped), gas valve, pilot, burners, gas shutoff valve and self cleaning burner
system (if equipped).
Filter models: Filter pump, oil/shortening return handle and flush hose (if equipped).
4. Drain Valve Handle (Blue) (Shown in the closed position)
Opens the drain valve so oil/shortening can be drained from the cook tank.
If the drain valve interlock feature is equipped, the appliance will stop heating if the drain
valve is opened.
5. Tank Drain Outlet
Oil/shortening exits the cook tank through the drain outlet when draining.
6. High Temperature Reset Button
This button may need to be pressed in the event that the high temperature limit has tripped.
7. Basket Hanger
For hanging and/or draining baskets when they are outside of the cook tank.
8. Gas Shutoff Valve
Shuts off the supply of gas to the gas valve.
9. Gas Valve Knob
The gas valve controls the flow of gas to the pilot and burners.
Turning the gas valve knob to the OFF position shuts off the gas supply to the pilot and
burners
10. Pilot
The pilot lights the burners when the water in the cook tank requires more heat.
11. Burners
Heats the oil/shortening inside the cook tank.
12. Self Cleaning Burner System (if equipped)
The self cleaning burner system cleans the burners when the appliance is turned ON.
1.10.2. OPERATION FEATURES SPECIFIC TO MODELS WITH FILTERS.
13. Filter Pump
The filter pump is used to pump oil/shortening from the filter pan back into the cook tank or
through the flush hose (if equipped).
14. Filter Pump Reset Button
This button may need to be pressed in the event that the filter pump circuit breaker has
tripped.
15. Oil Return Handle (Red)
Oil exits the cook tank through the drain outlet when draining.
OPERATION
L20-378 rev.4 (10/18) 21
1. Fill Line
2. Heat Tubes
3. Solid Shortening
4. Excessive Air Gaps
16. Filter Pan
Oil drained from the cook tank goes into the filter pan.
Filter media is located inside the filter pan.
17. Flush Hose Connection (if equipped)
Connect the flush hose here when using the flush hose feature.
18. Flush Hose Handle (Yellow) (if equipped)
Pulling this handle starts the flow of oil/shortening through the flush hose.
Pushing the handle in will stop the flow of oil/shortening through the flush hose.
19. Oil Reclamation Handle (Brown) (if equipped)
Pulling this handle out will start the flow of oil/shortening through the oil reclamation system.
Pushing this handle in will stop the flow of oil/shortening through the oil reclamation system.
1.11. FILLING THE COOKER TANK
Both liquid and solid shortening can be used in this appliance, but liquid is preferred. If solid
shortening is used it is recommended that you melt the shortening before adding it to the
appliance. You can melt solid shortening in the appliance, but you must be very careful not to
scorch the shortening.
1.11.1. FILLING THE TANK WITH LIQUID SHORTENING
To fill the tank with liquid shortening refer to the following procedure.
1. Ensure that the drain valve is completely closed and that there is no residual moisture
in the tank.
2. Fill the tank with oil. You may fill the tank to the “MIN LEVEL” mark or slightly below the
nominal level mark: the oil will expand slightly when it heats up, raising the level
slightly.
1.11.2. FILLING THE TANK WITH SOLID SHORTENING
To fill the tank with solid shortening refer to the following procedure.
1. Remove the tank rack.
2. Cut the solid shortening into cubes
no larger than one inch. ALWAYS
pack the shortening below,
between, and on top of the burner
tubes. Do NOT leave any large air
gaps. Use care when packing the
solid shortening into the tank. Do NOT bend or break the temperature or high limit
sensor probes. If these are damaged the appliance will not function properly.
CAUTION
This appliance is NOT designed for cooking with water. Fill with oil or shortening only.
WARNING
NEVER melt blocks of
solid shortening on top of
the heat tubes. This will
cause a fire and could
result in personal injury.
OPERATION
22
L20-378 rev.4 (10/18)
Solid State
I/0 ON/OFF
Switch
3. Once the appliance tank is firmly packed with shortening, the shortening must be
melted. If your appliance has a Melt Cycle option, use this to melt the shortening
automatically.
1.12. APPLIANCE START UP
Refer to the following procedure to start the appliance prior to operation.
1. Ensure that the drain valve is closed.
2. Fill the cook tank with oil/shortening. (See section 2.2 “Filling the Cook Tank”)
3. Light the appliance. (See “Lighting Instructions” section)
4. If the appliance is equipped with a controller, turn the controller on.
Solid State Thermostat:
Turn the I/0 (ON/OFF) switch to the I (ON) position
Computer and Digital Control:
Press the
*
button to turn the controller on.
*The specified button may appear slightly different then shown.
Refer to the operator’s manual for your appliance’s specific control
type to determine the exact appearance of each button and display.
Note: If your appliance has a self cleaning burner system, the burners may make a
popping sound immediately after the main burners light during startup. This noise
during startup is part of the normal operation of the self cleaning burner system and
should NOT continue during normal cooking & idle periods. (SCB Only)
5. The appliance is now on and heating the oil/shortening in the cook tank.
OIL TEMPERATURE
Keep the oil temperature in the fryer to a maximum of 190°C (374°F). Higher temperatures will cause
rapid breakdown of the oil and give you no faster cooking. At 205°C (401°F) to 210°C (410°F) the life of
the oil is only one third of its life at 190°C (374°F). In addition, increased decomposition causes the oil
to smoke badly even if the temperature is lowered to 190°C (374°F) again. High temperatures give you
no advantage, cost you money and increase the fire danger.
TEMPERATURA DELL’OLIO
Mantenere la temperatura dell’olio nella friggitrice fino a un massimo di 190°C. Temperature maggiori
causano un rapido degrado dell’olio, senza tuttavia eseguire una cottura più rapida. Da 205°C a 210°C
la durata dell’olio è inferiore di un terzo rispetto a quella a 190°C. Inoltre, l’accresciuta decomposizione
comporta una forte emissione di fumo, anche se la temperatura viene riportata di nuovo a 190°C. Le
alte temperature non prevedono vantaggi, sono antieconomiche e aumentano il rischio d’incendio.
WARNING
Oil/shortening must completely cover the heat tubes at all times while appliance is on.
WARNING
Oil/shortening level should NOT be allowed to fall below the minimum indicated level line at
any time. Dry firing of the fry tank will shorten tank service life and will void your warranty.
WARNING
NEVER operate the appliance with an empty fry tank. It will void the warranty.
OPERATION
L20-378 rev.4 (10/18) 23
Typical Timer Buttons*
7 x 14 in
(17.8 x 35.6 cm)
14 x 14 in
(35.6 x 35.6 cm)
18 x 18 in
(45.7 x 45.7)
14 x 18 in
(35.6 x 45.7 cm)
18 x 14 in
(45.7 x 35.6 cm)
1.5 LBS (0.68kg) 3 LBS (1.36 kg) 5 LBS (2.27 kg) 3 LBS (1.36 kg) 5 LBS (2.27 kg)
18 x 24 in
(45.7 x 61.0 cm)
20 x 20 in
(45.7 x 35.6 cm)
24 x 24 in
(61.0 x 61.0 cm)
34 x 24 in
(86.4 x 61.0 cm)
5 LBS (2.3 kg) 6 LBS (2.7 kg) 8 LBS (3.7 kg) 9 LBS (4.0 kg)
Maximum Allowable Load per Tank Size (W x L)
ΘΕΡΜΟΚΡΑΣΙΑ ΛΑ∆ΙΟΥ
∆ιατηρείτε τη θερμοκρασία λαδιού στη φριτέζα μέχρι 190 βαθμούς Κελσίου. Υψηλότερες θερμοκρασίες θα
αλλάξουν τη σύνθεση του λαδιού πολύ σύντομα και δεν ψήνετε γρηγορότερα. Η δυναμικότητα του λαδιού
στους 205-210 βαθμούς Κελσίου είναι μόνο το ένα τρίτο της δυναμικότητάς του στους 190 βαθμούς
Κελσίου. Επιπλέον η αυξημένη αποσύνθεση του λαδιού, σε θερμοκρασίες πάνω από 190 βαθμούς
Κελσίου, κάνει το λάδι να καπνίζει άσχημα κι αν ακόμη κατεβάσετε τη θερμοκρασία κατόπιν πάλι στους
190 βαθμούς Κελσίου. Οι υψηλές θερμοκρασίες δε σας παρέχουν κανένα πλεονέκτημα, σας κοστίζει
περισσότερα χρήματα και αυξάνουν τον κίνδυνο πυρκαγιάς.
1.13. COOKING
To ensure the quality of the food you cook in this appliance, follow the preparation instructions from
the food manufacturer. When the appliance is not in use, the oil/shortening should be cooled and
covered to prevent contamination.
1.13.1. TIMER OPERATION
Not all control types include timers. Timers provide accurate cook times for multiple product
quantities and types. Refer to the operator’s manual for your appliance’s specific control type to
determine how to set the cook timers if equipped.
To start a timer: Press the appropriate timer button.
1.13.2. BASKET LIFT OPERATION
If the appliance is equipped with basket lifts, place the basket onto the basket lift prior to starting
the timer(s). The basket(s) will be lowered into the cook tank when the timer cycle starts. At the
end of the preset cooking time, the basket lift will raise the basket out of the cook tank.
1.13.3. SPINFRESH
TM
If the appliance is equipped with SPINFRESH
TM
, place the basket directly onto the basket lift pin
and close the lid prior to starting the timer(s). The basket(s) will be lowered into the cook tank
when the timer cycle starts. At the end of the preset cooking time, the basket lift will raise the
basket out of the cook tank and spin the basket to remove excess oil. The lid may be opened
during the cooking cycle but must be closed prior to the spin cycle.
WARNING
Dry fired heat tubes are extremely hot, will shorten its service life and will void your warranty.
WARNING
NEVER open the lid or reach into the SPINFRESH
TM
enclosure during the spin cycle. Serious
injury could result.
OPERATION
24
L20-378 rev.4 (10/18)
Typical French Fry Cook Times
Fry Thickness 350F 360F 370F
(177C) (182C) (188C)
Thin 2:45 2:30 2:15
medium 3:45 3:30 3:15
Thick 4:15 4:00 3:45
This table is for reference only. Please refer
to the product manufacturer’s specifications to
determine exact cook temperatures and
ti
1.13.4. ADDITIONAL CONTROLLER FUNCTIONS
Some controllers have additional functions not described in this manual. If your appliance’s
controller has additional functions, refer to the controller’s operation manual to access these
functions.
*The specified buttons and/or displays may appear slightly different then shown. Refer to
the operator’s manual for your appliance’s specific control type to determine the exact
appearance of each button and display.
1.14. COOKING TIPS
Always follow the food manufacturer’s directions.
The lower the oil temperature, the longer the cooking time and the greater the fat absorption.
NEVER overfill fryer baskets. Overfilling can result
in soggy, greasy product.
When removing baskets from the cook tank, shake
gently to remove excess oil.
Never leave a basket over the fryer. The heat from
the cook tank will continue to cook the product.
Oil/shortening quality can effect product quality.
Keep salt and water away from the oil/shortening to
maintain its life. Oil/shortening filtration removes
crumbs from the oil which will also extend its life.
1.15. APPLIANCE SHUTDOWN
There are two shutdown modes of appliance operation: STANBY and COMPLETE. The standby
mode removes the ability of the appliances main burners to operate. Complete shutdown turns off the
gas supply to the appliance. Refer to the following procedures to enter the appropriate shutdown
mode.
1.15.1. STANDBY MODE
1. Turn the temperature controller or thermostat OFF.
Solid State Thermostat:
Turn the I/0 (ON/OFF) switch to the O (OFF) position
Computer and Digital Control:
Press and hold the
*
button to turn the controller OFF.
*The specified button may appear slightly different then shown. Refer to the
operator’s manual for your appliance’s specific control type to determine the exact
appearance of each button and display.
PREVENTATIVE MAINTENANCE
L20-378 rev.4 (10/18) 25
1.15.2. COMPLETE SHUTDOWN
1. Turn the temperature controller or thermostat OFF..
Solid State Thermostat:
Turn the I/0 (ON/OFF) switch to the O (OFF) position
Computer and Digital Control:
Press and hold the
*
button to turn the controller OFF.
*The specified button may appear slightly different then shown. Refer to the
operator’s manual for your appliance’s specific control type to determine the exact
appearance of each button and display.
2. Turn the ON/OFF knob on the gas valve clockwise to the OFF position.
3. The appliance is now completely shut down and can be cleaned if desired.
2. PREVENTATIVE MAINTENANCE
2.1. DAILY PREVENTATIVE MAINTENANCE
Performing the preventative maintenance steps below on a daily basis will keep your equipment safe
and at peak performance. During the cooking process, oil/shortening may spill and splatter and
requires immediate attention. Furthermore, during the cooking process, particles, crumbs and
crackling collect inside the cooker tank reducing product quality and decreasing oil/shortening life. If
you are producing high quantities of fried food and/or frying heavily battered food, it may be
necessary to perform these steps more then once a day.
2.1.1. FILTERING WITH A FILTER DRAWER (IF EQUIPPED)
Refer to the following procedure to filter when the appliance is equipped with a filter drawer.
1. Turn the appliance OFF.
2. Pull the blue drain handle down to drain oil/shortening from the cooker tank into the filter pan.
3. Pull the red handle to turn the pump on to circulate oil/shortening through the filter media.
4. To refill the tank, lift the blue drain handle up.
5. When the tank has completed filling, push the red handle to deactivate the pump.
6. Assure that the oil/shortening level is above the minimum level line. Additional oil may need
to be added to the cook tank.
7. The oil/shortening in the cooker tank has now been filtered.
8. Replace the filter media and clean the filter pan following the procedures mentioned in this
manual.
OFF
ON
Matchless Ignition
WARNING
Serious injury could result from direct contact with hot surfaces and/or oil. Always
wear apron, heat resistant gloves for skin protection and goggles for eye protection
PREVENTATIVE MAINTENANCE
26
L20-378 rev.4 (10/18)
1. Filter Pan
2. Filter Pickup Assembly
3. Filter Strainer Cap
4. Filter Paper
5. Filter Screen
2.1.2. FLUSH HOSE OPERATION (IF EQUIPPED)
The cooker tank can be rinsed cleaned by using a filter flush hose (if equipped). Refer to the
following procedure to operate the filter flush hose.
1. Turn the appliance OFF.
2. Pull the blue drain handle down to drain oil/shortening from the cooker tank into the filter pan.
3. Connect the filter flush hose to the quick connecting fitting.
4. Point the filter hose nozzle outlet into the cooker tank.
5. Pull the yellow handle to turn the pump on and allow oil/shortening to flow through the flush
hose.
6. To refill the tank, lift the blue drain handle up.
7. When the tank has completed filling, push the yellow handle to deactivate the pump.
2.1.3. REPLACING THE FILTER MEDIA (IF EQUIPPED)
Refer to the following procedure to replace the filter media if the appliance is equipped with a filter
drawer.
1. Detach the pickup tube from the filter pickup assembly by unscrewing it (counterclockwise),
at the knurled fitting, from the threaded fitting on the filter screen.
2. Slide off the filter paper clip and remove used filter paper from filter screen. Replace with
new filter paper, ensuring that the hole in the paper is on the top, so that threaded fitting in
filter screen protrudes through it.
3. Fold filter paper to the underside of the filter screen and replace filter paper clip.
4. Re-attach filter pickup tube to the filter screen
by screwing it (clockwise) into the threaded
fitting in filter screen.
5. Reinstall the filter pickup assembly into the filter
system by placing the newly covered screen
portion of the assembly into the filter pan and
connecting the quick disconnect on the filter
pickup assembly into white donut fitting on the
left-hand side of the appliance. Ensure that it
snaps tightly and securely into donut fitting.
PREVENTATIVE MAINTENANCE
L20-378 rev.4 (10/18) 27
WARNING
Serious injury could result from direct contact with hot surfaces and/or oil. Always wear apron,
heat resistant gloves for skin protection and goggles for eye protection
WARNING
DO NOT leave the appliance unattended during cleaning.
WARNING
Read the operation section of this manual prior to filling or operating the appliance.
2.1.4. APPLIANCE INSPECTION
Check that the high temperature limit and temperature probe are in the correct position and
secured in place.
Check that wires and cords are not frayed or loose in and out of the cabinet.
Check around the appliance for loose parts or accessories that need to be secured or other
foreign items (ex: Aerosol cans) that should be removed from the area.
Check for oil/shortening leaks around the in and out of the cabinet and around the
appliance.
2.1.5. CLEANING THE COOK TANK
1. Turn the appliance off. Drain all the oil/shortening from the tank and allow the tank to cool.
2. Remove baskets, tank rack and basket hanger for cleaning.
3. Using the cleaning brush, remove all the loose debris and scrub all tank surfaces.
4. For tougher carbonized oil/shortening and carbon buildup scrub tank using a Scotchbrite or
other abrasive pad.
5. Wipe residue with a clean damp cloth and carefully dry any remaining oil/shortening
droplets from the tank before returning oil/shortening into the tank.
6. Clean and dry baskets, tank rack and basket hanger before reinstalling.
2.1.6. CLEANING THE CABINET
1. Wipe any spilled oil/shortening, dust and lint from the cabinet exterior with a clean damp
cloth and a mild food grade detergent .Be careful not to get any water or detergent in the
oil/shortening. Use a nonabrasive pad for tougher stains if needed.
2. Remove detergent from all surfaces.
3. Cleaning the interior cabinet requires a clean cloth to remove any oil/shortening, dust, lint
or filter powder (i.e.: Magnesol) from the interior of the cabinet.
WARNING
The power supply must be disconnected before cleaning and servicing this appliance!
WARNING
The contents of the crumb catch and/or filter pan of any filter system must be emptied into a fireproof
container at the end of the frying operation each day. Some food particles can spontaneously combust
into flames if left soaking in certain oil/shortening materials.
PREVENTATIVE MAINTENANCE
28
L20-378 rev.4 (10/18)
2.1.7. FILTER CLEANING (IF EQUIPPED)
1. Unscrew filter strainer cap from pickup tube and gently tap it to dislodge any crumbs from the
slots. Use a clean cloth to remove any remaining crumbs and reattach.
2. Scrape all loose debris and crumbs from filter pickup assembly and filter pan with the filter
scoop shovel.
3. Remove filter pickup and place in pot sink, power soak sink or dishwasher for cleaning. Be
sure to rinse thoroughly and dry all surfaces before re-assembly.
4. Wipe the filter pan with clean damp cloth and a food grade detergent. If necessary place pan
in pot sink to rinse all the detergent from the surfaces and dry all surfaces before re-
assembly.
2.2. WEEKLY PREVENTATIVE MAINTENANCE
Performing the preventative maintenance steps above on a daily basis will keep your equipment
clean and safe. On a weekly basis these additional steps should be performed.
1. Turn the fryer off. Allow the oil/shortening to cool to before pulling the fryer away from the hood.
Hint: This maintenance may be ideal to perform on the day the oil/shortening is being changed
so no oil/shortening is present in the tank or filter.
2. Disconnect the power cord(s), gas hose, and retention lanyard.
3. Wearing your protective gear, pull the fryer away from the hood.
4. Check that vent hood drip cup is empty and not dripping oil/shortening into the flue.
5. Check that the hood baffles are clean and not dripping oil/shortening into the flue.
6. Clean the fryer sides, back and the flue area, it may be necessary to use a non-abrasive pad to
scour and a putty knife to scrape the oil/shortening buildup. With a clean damp cloth and food
grade detergent wipe the area clean.
7. Wipe up any excessive oil/shortening on the power cord(s) and gas hose with a dry cloth.
8. Check flue pipe for any foreign debris/object and remove if found.
9. Reattach power cord(s), gas hose, retention lanyard and push fryer back under the hood.
2.3. MONTHLY PREVENTATIVE MAINTENANCE
Food debris and oil/shortening can buildup inside the tank. Performing the monthly preventative
maintenance steps below will keep your equipment safe and at peak performance. If you are
producing high quantities of fried food and/or frying heavily battered food, it may be necessary to
clean these components more then once a month.
2.3.1. BOIL OUT PROCEDURE
Wear protective gloves and clothing when cleaning and draining the appliance. Oil/shortening
may spatter and will cause injury to personnel.
1. Read the “operation” section of this manual prior to filling or operating the appliance.
2. Turn the appliance off. Drain all the oil/shortening from the tank and allow the tank to cool.
The container must also be able to withstand 400F (205C) temperatures.
3. Remove baskets, tank rack and basket hanger for cleaning.
4. Remove and discard any large debris inside the tank.
5. Close the drain valve and fill the tank with potable water to the level lines.
PREVENTATIVE MAINTENANCE
L20-378 rev.4 (10/18) 29
WARNING
The power supply must be
disconnected before cleaning
and servicing this appliance!
6. Place the appliance into boil mode:
Models with Solid State Thermostat: Put the thermostat into boil mode by flipping the power
switch in the following order (I- O - I - O - I) within 3 seconds. The power (green LED) and
heating (yellow LED) will be lit and the check (yellow LED) flashing.
Models with Digital Control: This controller does not have a boil mode. With the controller
turned on, press the P key. If LOC displays, press the left timer twice and then the right timer
twice. Press the P key two more times to show the set temperature. Use the down arrow to
change the set temperature to 200°F (93°C). Hold the P key to save.
Models with Computer: Turn the appliance ON. The controller will recognize that there is
water in the tank and automatically enter boil mode. To enter boil mode manually, press the
Temp Key then keys 2, 1, 2 for degrees F or 1, 0, 0. for degrees C.
7. Once the water reaches a simmer, add 8 to10 ozs (227 to 283 g) of Pitco cleaner for every 25
lbs (11.3 kgs) of oil/shortening your fryer is rated to hold.
8. Simmer for 1 minute. (The water should never be allowed to boil as this may splash over the
tank side and cause permanent damage to the components.)
9. Turn the appliance OFF and allow the fryer to soak for 15 to 30 minutes, allowing the cleaner
to soften the oil/shortening deposits and carbon.
10. Scrub the inside of the tank using a cleaning brush safe for hot water. Care must be taken to
remove all the foreign material on the tank, heating tubes, sidewalls and other components in
the tank.
11. Drain the water from the tank.
12. Once the tank has cooled, rinse with clean potable water thoroughly.
13. Remove all remaining water and residue with a clean dry cloth.
14. Clean and dry baskets, tube rack and basket hanger before reinstalling
15. Close the drain valve and fill the cooker tank with oil/shortening.
2.3.2. TEMPERATURE CHECK
1. Use a high grade pyrometer or digital thermometer suitable for temperature up to 380F
(182°C). Place the thermometer in the oil above the tip of the fryer’s temperature probe with
in 1” (2.54 cm) 25.4 mm). Be sure not to touch the heat tube since this will measure
incorrect temperatures.
2. Reference the following steps that apply to the appliance’s control type.
Models with Solid State, Digital or Computer Controls:
Check that the controllers setpoint and thermometer is within ± 5F (± 3°C). If your
measurement are off, re-measure again before contacting an Authorized Service Company
for further assistance.
2.4. ANNUAL/PERIODIC PREVENTATIVE MAINTENANCE AND INSPECTION
This section should ONLY be performed by a qualified service
technician as part of a regular kitchen maintenance program.
This inspection should take place a minimum of once a year by
an Authorized Service Technician recommended by Pitco. It
may be necessary perform this inspection more then once a
year.
PREVENTATIVE MAINTENANCE
30
L20-378 rev.4 (10/18)
2.4.1. SAFETY EVALUATION
Check power cord and plug.
Check all exposed wiring connections, switches, and indicator lights.
Check legs, casters, wheels, plate welds and ensure all nuts and bolts are secured.
Check conditions of flexible gas line and verify fryer retention / lanyard system is in place.
2.4.2. MECHANICAL INSPECTION
Check frypot for shortening leaks and excessive oil build up
Check for oil migration (Clean as required)
Check hood drain cup, ensure it is empty and not dripping into the flue.
Check hood baffle for clean surface, oil/water condensate can drip on and into the flue.
Check flue for foreign debris and hood down draft currents.
Check drain/filtration system (if equipped) for leaks
Check for missing fryer parts, i.e.: cover strips
Check for missing fasteners
2.4.3. TEMPERATURE CONTROL SYSTEM
Check electrical connections and harnesses
Check temperature probes and limits for carbon build up and plating. Clean as required
Check proper mounting of probes and sensors and all fasteners are secure.
Check thermistor probe resistances for stability.
Check DVI Drain Valve Interlock drops out controller.
Check Controller/thermostat features to ensure they are functioning.
Check Temperature Calibration
2.4.4. FILTER SYSTEM (IF EQUIPPED)
Check electrical connections and harnesses.
Check IEC power cords are fully engaged and secure.
Check for any air or shortening leaks and for excessive oil build-up.
Check O-Ring on filter pickup tube and replace as needed.
Check filter strainer on pickup tube.
Check operation of drain valve and DVI drain valve interlock.
Check operation of return oil valve and its pump switch.
Check operations of flush hose quick disconnect (if equipped), clean and lubricate as
needed.
Check all hardware in filter pan.
Check filter operation by filtering the fryers.
Check pump motor amp draw compare to nameplate amperage.
Check pump and motor, clean any excess oil from pump assembly.
Check all filter hoses for leaks and integrity.
2.4.5. GAS COMBUSTION SYSTEM
Check for gas leaks.
Check and clean vent tube on gas valve pressure regulator.
Check burners, clean debris and grease from pilot and pilot orifice tips.
Check self cleaning burner system (if equipped) that it activates when the appliance is turned
on and NOT during normal cooking & idle periods.
Check and adjust burner manifold gas pressure to nameplate reading.
Check incoming gas pressure when all gas appliances are on.
Check ignition system and adjust pilot flame as required.
Check flame sensor reading.
Check gap spacing and clean igniter.
Recheck for gas leaks after inspection.
2.5. VENTILATION HOOD
Proper ventilation hood operation is very important for the correct operation of this appliance and the
safety of personnel. The ventilation hood should be inspected at the time of installation of this
appliance to insure that it will operate properly in conjunction with the appliance. A regular schedule
of examination, in accordance with ANSI/NFPA 96 latest edition and/or local codes must be followed.
TROUBLESHOOTING
L20-378 rev.4 (10/18) 31
3. TROUBLESHOOTING
3.1. POWER FAILURE
If electric power is removed for any reason, the appliance will shut down.
Wait five minutes after the power is restored before attempting to restart the appliance. This will allow
time for any gas that may have accumulated in the burner or tubes to dissipate.
To restart the appliance, follow the appliance start up procedure in section 2.2.
3.2. HIGH TEMPERATURE LIMIT SWITCH
This appliance is equipped with a high temperature limit switch. The high temperature limit switch will
stop the appliance from functioning if the oil temperature in the cook tank reaches an unsafe
temperature. In the event that the high temperature limit has tripped, please refer to the following
procedure to reset the switch.
a. Turn the appliance off.
b. Allow the appliance ample time to cool to room temperature.
c. Add oil/shortening to the cook tank as needed.
d. Press the high temperature reset button.
e. The high limit switch is now reset and the appliance is ready for start up.
3.3. DRAIN VALVE INTERLOCK & FLOAT SWITCH (NOT ON ALL MODELS)
If your appliance is equipped with a drain valve interlock circuit, the appliance will stop heating if the
tank drain valve is opened. If your appliance is equipped with a float switch, the appliance will stop
heating if the oil/shortening level reaches an unsafe height. In some cases the appliance will turn off.
Refer to the following procedure to resume operation after the drain valve interlock is tripped.
1. Turn the appliance OFF (if not already OFF).
2. Close the tank drain valve and fill the tank with oil/shortening.
3. Turn the appliance ON.
3.4. SELF CLEANING BURNER SYSTEM (NOT ON ALL MODELS)
If your appliance is equipped with the self cleaning burner system, the appliance should behave as
outlined in the table below. A cleaning cycle will execute every time the appliance is turned “ON” from
an “OFF” state. The thermal cut out switch is designed to disable the appliance if the Self Cleaning
Burner System malfunctions and remains activated for an extended period of time or if there is a
downdraft into the flue or a blocked flue situation.
CAUTION
DO NOT attempt to operate this appliance during a power outage.
WARNING
DO NOT add oil/shortening to the tank until it has been given ample time to cool down.
Failure to do so may result in damage to the appliance and/or injury to the operator.
HighTemperatureResetButton
TROUBLESHOOTING
32
L20-378 rev.4 (10/18)
1- SCBS Reset Button
3.5. RESETTING THE SELF CLEANING BURNER SYSTEM TEMPERATURE LIMIT SWITCH
1. Turn the appliance off.
2. Allow the appliance ample time to cool to room
temperature.
3. Press the SCBS high limit reset button. The reset
button is located behind the front panel at the top
of the main burners.
4. The SCBS high limit switch is now reset and
ready for startup.
5. If the SCBS high temperature limit switch
continues to trip, have the appliance inspected by
an Authorized Professional.
Event Duration Indication
Turn appliance “ON” N/A
Control Illuminates, pilot sparks and ignites. Pre-Purge
pulse is initiated.
Pre-Pur
g
e Pulse 2 seconds
A
ppliance operates briefl
y
and stops. Pilot remains lit.
Interwaitin
g
period 1 5 seconds
A
ppliance does not operate. Pilot remains lit.
Cleaning Pulse 6 seconds
Main valve operates, lighting main burners. SCBS valve
operates, feeding gas to the SCBS Arm. The SCBS arm
ignites, initiating a brief burn at the main burner orifice of
each burner.
Interwaiting period 2 8 seconds
The Main and SCBS valves de-energize for this period.
The pilot remains lit.
Normal operation
resumes
N/A
The appliance operates normally and begins to heat up.
The SCBS Valve remains de-energized until power to
the appliance is recycled. There is no flame on the
SCBS Arm. There is no burn at the main burner orifices.
TROUBLESHOOTING
L20-378 rev.4 (10/18) 33
3.6. TROUBLESHOOTING CHARTS
3.6.1. FRYER TROUBLESHOOTING CHART
3.6.2. FILTER TROUBLESHOOTING CHART (IF EQUIPPED)
Problem Probable Causes Corrective Actions
Controller does
not activate.
No power to appliance. Check main building power supply.
Controller not turned on. Turn on controller.
Power Cord loose or not
connected.
Connect power cord.
Main circuit breaker to
appliance has tripped.
Reset circuit breaker
Appliance fuse has blown. Contact Authorized Service Company.
Controller is on
and appliance will
not heat up.
High temperature limit has
tripped.
Allow appliance to cool and reset High
temperature limit.
SCBS thermal limit switch has
tripped.
Depress button on thermal limit switch to reset. If
problem continues, Contact Authorized Service
Company.
Appliance will not
maintain
temperature
properly.
Faulty temperature probe. Contact Authorized Service Company.
Faulty High temperature limit. Contact Authorized Service Company.
Computer display
shows off and can
not be turned on.
Faulty computer Contact Authorized Service Company.
Problem Probable Causes Corrective Actions
Filter pump does
not activate.
Filter pump circuit breaker has
tripped.
Reset circuit breaker.
Oil/shortening is
returning to the
tank slowly or not
at all.
Dirty filter paper Change filter paper.
Strainer cap dirty Remove strainer cap and clean.
Filter pan not pushed in
completely.
Push filter pan in.
Excessive air
bubbles are in the
oil being returned
to the tank.
Pickup tube screen not tight. Tighten pickup tube screen cap.
Pickup tube screen cap
missing
Locate and install pickup tube screen cap.
Filter pan not pushed in
completely
Push filter pan in to complete connection.
Drain valve is
closed, but the
computer
controller still
displays
“DRAINING”
Blue drain valve handle not
completely closed
Verify that drain valve handle is completely
closed.
Improperly adjusted or
defective drain switch.
Contact Authorized Service Company.
TROUBLESHOOTING
34
L20-378 rev.4 (10/18)
3.7. COMPUTER & DIGITAL CONTROLLER DISPLAYS (IF EQUIPPED)
If your appliance is equipped with a computer or digital controller it may display the following
messages on its display.
Display Explanation Action
Appliance is in melt cycle
Continue with melt cycle or exit melt cycle to
return to normal operation.
Oil/shortening temperature is
low.
Wait for appliance to heat up.
The cook tank has reached the
set temperature.
Appliance is ready to start cook cycle.
Indicates program mode is
password protected.
Enter password or wait for controller to exit
program mode.
Incorrect probe reading. Contact Authorized Service Company.
Oil/shortening has reached an
unsafe temperature.
Turn off appliance. Allow ample time for
appliance to cool before turning on.
Incorrect probe reading. Contact Authorized Service Company.
Drain valve is open while
controller is on.
Turn off appliance. Close drain valve before
turning appliance back on.
Ignition system has locked out. Contact Authorized Service Company.
Controller is OFF. Turn controller on.
L20-378 rev.4 (10/18) 35
NOTES
L20-378 rev.4 (10/18)
SPINFRESH
TM
is a trademark of Spinfry inc.
Annual service to this appliance by an authorized person is recommended. Do not modify this appliance:
servicing must only be carried out by an authorized person. For service and parts, minor adjustments,
fault finding, or if this appliance cannot be adjusted to operate correctly, contact:
In the event of problems with or
questions about your order, please
contact the Pitco Frialator factory at:
(603) 225-6684 World Wide
Website Address: www.pitco.com
In the event of problems with or questions
about your equipment, please contact the
Pitco Frialator Authorized Service and Parts
representative (ASAP) covering your area, or
contact Pitco at the numbers listed to the left.
MAILING ADDRESS – P.O. BOX 501, CONCORD, NH 03302-0501
SHIPPING ADDRESS – 39 SHEEP DAVIS RD, PEMBROKE, NH 03275
